African Satellite World and Sat Gear

African Satellite World and Sat Gear

This RAT race is not over until it's over,
Someone help with a screen shot of v7 combo powervu key Editing.
 
This is a tricky set up. I presume one of the stbs must have lnb power off to avoid stb conflicting diseqc commands? And also you don't need the two way switch if you only have one stb, correct?
Not a very useful set up since the decoders can't independently send the 18V / 13 V command to the lnb. Only one at a time while the other decoder looses signal and goes idle. or both decoders be used but they must tune to the same channel. Now that can be achieved by just using a single decoder and outputting the signal to two different tv screens through AV output and HDMI output from a single decoder
 
Not a very useful set up since the decoders can't independently send the 18V / 13 V command to the lnb. Only one at a time while the other decoder looses signal and goes idle. or both decoders be used but they must tune to the same channel. Now that can be achieved by just using a single decoder and outputting the signal to two different tv screens through AV output and HDMI output from a single decoder
Have you tried it or how have you come with such a conclusion? Just curious
 
This RAT race is not over until it's over,
Someone help with a screen shot of v7 combo powervu key Editing.

Here is the procedure but no screenshots though.

Go to Menu, scroll upwards to Conditional Access, click OK, go to Key Edit, click OK, go to PowerVu and click OK, select one of the provisions for key editing, press the Red button on your remote, input Provid, Idx & Key Data by pressing OK on highlighting any then use the onscreen keypad and then click Yellow to save.

Press Exit, then select Yes on the pop-up/confirmation screen then press OK and Exit.
 
Provid ?
Idx ?
Sony or any as an example .

Provid is often 0000 whereas
Idx is 00 for the first line of code and 01 for the second line of code.
All PowerVu codes has two lines.

Please check your Inbox.
 
iSATbox TSR-141HD TRANSITIONAL SOFTWARE [NURSTAR LEG A-25HD]
It is now possible to upgrade iSATbox TSR-141HD with NURSTAR LEG A-25HD software as a transitional software. Test has been personally confirmed to be working 100%. The decoders' motherboard chassis number "K3_MO1_V1.3_150420" belongs to the family of the "K3 Processor"; this is the exact processor running in GSKy v.6HD & v.7HD. Incase of reviving a bricked decoder, use the rs232 Up-Grade tool "K3_TCOM_UPG_TOOL"

PS!! AT THIS STAGE DON’T RENAME THE TRANSITIONAL SOFTWARE TO “auto_burn.fac”
While injecting this software, observe the following procedures on the iSATbox TSR-141HD satellite receiver:
1. Factory Reset decoder and erase all User Preference data including channel list & EMU keys.
2. Switch rocker “OFF” at the rear and unplug from the power mains.
3. Power “ON” decoder and Factory Reset yet again.
4. Insert USB pen drive into decoder, on RCU press Menu >>>Navigate to Tools >>>USB UpGrade
5. Select Mode as “ALL CODE”.
6. After successful upgrade and as a rule of the thumb, Factory Reset the decoder yet again.

This software is also compatible with the satellite receiver 7STAR 2001 HD Hyper.

Download NURSTAR LEG A-25HD software from here: Downloads - PEACESAT COMMUNICATION

iSATbox TSR-141HD .png

 
Anyone who's ever used a usb WiFi dongle on a strong which one would you recommend?
 
Some one please help me with s*ny 39** keys . am really stack even after upgrade to 4.18 (strong srt 4950H)
 
6ft on Vaz*ssssshhh Yahsat 52.5e from Nairobi. Yawezekana Hayawezekani?
 
Back
Top Bottom