zantel Router unlocked!

sijui nini

sijui nini

JF-Expert Member
Sep 29, 2010
2,553
1,285
unaweza kutumia modem yoyote katika router yako ya huawei d100 baada ya kui unlock..normally imekuwa locked kwa zantel modems only !!
 
sijui nini said:
unaweza kutumia modem yoyote katika router yako ya huawei d100 baada ya kui unlock..normally imekuwa locked kwa zantel modems only !!
Click to expand...

i guess it`s better kama utatoa maelezo ya kina na sisi pia tufahamu kuhusiana na hii free post yako.
 
sijui nini said:
unaweza kutumia modem yoyote katika router yako ya huawei d100 baada ya kui unlock..normally imekuwa locked kwa zantel modems only !!
Click to expand...

Unataka usaidiwe ku-unlock au umefanikiwa ku-unlock? Which is which?
 
hiyo ni taarifa wadau...!! saiz natumia modem ya zain ina lain ya voda kwenye router ya zantel...mambo mseto!! Namaanisha kwa wanaotumia routers za zantel, unaweza kuichakachua ukaweka modem yoyote ikafanya kazi!!
 
this is the firmware version (396.11.00.09.108) capable to remove network limitation on Huawei D100 Router.
Download it from this link or http://www.megaupload.com/?d=UE59P3R3 http://www.zshare.net/download/65148244aff17c80/ and read instruction inside before start




updating and unlocking
To unlock the Huawei D100/D100T follow these instructions:

  1. Download an update from above and extract it to your computer:
  2. Before flashing make sure your computer and the Huawei D100 won't lose power during the process as it could potentially brick your Huawei D100!
  3. Power on the Huawei D100 and connect it to computer through an Ethernet cable
  4. Launch FmcUpdate.exe from the extracted files
  5. Click the "Check" button to detect your Huawei D100 and shift it to update mode
  6. Click the "Upgrade" button to start the update
  7. Wait a couple minutes until the whole progress is accomplished
  8. After upgrade, disconnect the Ethernet cable and push the reset button of the Huawei D100 (in the lower right corner of the backside) or restore factory defaults in the webinterface (open http://192.168.1.1 in your browser and enter "admin" as default password, then go to Advanced Settings | System | Restore Defaults | Restore).
    note: If you do not restore to factory defaults after the update, your USB modem won't be detected properly and the "Connection" page will say "The USB Modem is nonexistent"
  9. Connect your USB modem to the Huawei D100 port only when it's switched off!
  10. Turn-on the router and go to the GUI by opening http://192.168.1.1 in your browser and enter "admin" as password.
  11. To activate an access profile for your network operator, go to Advanced Settings | Dial Up Settings | Profile Settings and chose your provider from the Profile List. If your provider's settings are not included, just create a new profile by entering a Profile Name and all the other information required below and click on Save.
  12. Afterwards go to Advanced Settings | Dial Up Settings | PPP Settings and make sure the correct profile is chosen in the Profile List. If not, chose the correct one and hit Apply.
  13. Now your router is ready to share your broadband (remember that your USB modem must also be unlocked!).
  14. You might want to enable (really) secure WiFi-encryption under Advanced Settings | WLAN Settings | WLAN Advance Settings where you should set WPA-PSK|WPA2-PSK as Encryption Mode and TKIP+AES as WPA Encryption. Lastly enter the WPA Pre-Shared Key, which should be not too easy to guess and hit Apply.

internal photos
download
Click to expand...
 
have u tried that?? just try it and you will see... i tried that also...kilichotokea najua mwenyewe... but there is another way round
 
You must log in or register to reply here.

Similar Discussions

Back
Top Bottom
Forums
New posts
Post thread
Back